Bicroelast TPP technical characteristics. Roofing material Bikroelast TPP - technical characteristics and laying technology. Roll roofing: binder weight
Bicroelast is a roll-on, welded waterproofing material.
Application area:
It is intended for the device of a waterproofing of buildings, constructions and building constructions.
Structure:
Bicroelast is obtained by double-sided application of a bituminous binder consisting of bitumen, filler and technological additives to a fiberglass (fiberglass, fiberglass) or polyester base, followed by the application of protective layers on both sides of the web. Coarse-grained (shale), fine-grained (sand) dressings and a polymer film are used as protective layers.
Brands:
Depending on the type of protective layers and application area, Bikroelast is produced in the following grades:
Bicroelast K- with coarse-grained dressing on the front side and a polymer film on the deposited side of the web; It is applied to the device of the top layer of a waterproofing with protection against the sun.
Bicroelast P- with fine-grained dressing or polymer film on the front side of the web and polymer film on the underside of the web or fine-grained dressing on both sides of the web; used for the device of the lower layers of waterproofing.
EPP
CCI
HPP
EKP
TCH
HKP
Material specification table:
| Parameter name | EPP | CCI | HPP | EKP | TCH | HKP | |
| Weight 1 m2, kg, (±0.25 kg) | 2,5 | 2,5 | 2,5 | 4,0 | 4,0 | 4,0 | |
| Breaking strength in the longitudinal/transverse direction, N, not less than | polyester | 350/- | - | - | 350/- | - | - |
| fiberglass | - | 700/700 | - | - | 700/700 | - | |
| fiberglass | - | - | 300/- | - | - | 300/- | |
| Flexibility temperature on the beam R=25mm, °С, not higher | -10 | -10 | -10 | -10 | -10 | -10 | |
| Heat resistance, °С, not less than | 85 | 85 | 85 | 85 | 85 | 85 | |
| Protective coating type | upper side | film without logo | film without logo | film without logo | slate | slate | slate |
| welding side | film with logo | film with logo | film with logo | film with logo | film with logo | film with logo | |
| Length / width, m | 15x1 | 15x1 | 15x1 | 10x1 | 10x1 | 10x1 | |
| Loss of dressing, g/sample, no more | 1 | 1 | 1 | ||||
| Waterproof at a pressure of at least 0.2 MPa, for 2 hours | absolute | absolute | absolute | ||||
| Waterproof for 72 hours at a pressure of 0.001 MPa | absolute | absolute | absolute | ||||
| Mass of binder from the surfaced side, kg/sq.m., not less than | 1,5 | 1,5 | 1,5 | 1,5 | 1,5 | 1,5 | |
| Water absorption within 24 hours, % by mass, no more | 1 | 1 | 1 | 1 | 1 | 1 |
Manufacturing jobs:
according to the "Guidelines for the design and installation of roofs made of bituminous materials of the TechnoNIKOL Corporation", can be used in all climatic regions according to SNiP 23-01.
TechnoNIKOL Corporation offers modern Construction Materials that meet Russian and European quality standards, which include roofing roll materials, bitumen, materials for.
Bicroelast TPP is a business-class bituminous roofing and waterproofing material that is used for low-slope roofs and for protecting foundations and other building structures from moisture. Special modified components that are added to the binder composition directly during the manufacturing process of the material give it unique properties. Roll roofing Bikroelast TPP does not lose elasticity at temperatures down to -10 ° C and has excellent heat resistance.
The basis of the material is durable fiberglass. A layer of bitumen is applied to its surface, which is protected on both sides with a polymer film. Waterproofing with the CCI marking is used as a lining material in all climatic zones of our country. Bikroelast CCI is produced by the TechnoNICOL concern, which guarantees compliance with the technical characteristics of its products Russian standards quality and fire safety.
The main advantages and features of the rolled roof Bikroelast TPP
An important feature of Bicroelast is the preservation of flexibility, strength and other performance characteristics over a wide temperature range. This waterproofing material has the following characteristics:
- high tensile strength;
- absolute water tightness;
- decay resistance;
- frost resistance and heat resistance;
- long service life;
- ease of installation.
Thanks to the fiberglass base, the material is able to withstand quite serious loads. It can also be used in rooms with high humidity.
Mounting technology and scope of Bicroelast TPP
Installation of the rolled roof Bikroelast TPP is carried out by welding using propane burners. However, in the absence of the possibility of using open fire, it can also be glued to the mastic. On the cleaned base (with pre-sealed cracks, chips and other defects), to increase adhesion, a special primer must first be applied - a bitumen primer or bitumen diluted with gasoline in a ratio of 1: 3. Laying is carried out on a reinforced sand-cement screed or concrete slabs with an overlap of 8 - 10 cm. Scope of application: installation of vapor barrier, the lower lining layer of the roof, waterproofing of basements, foundations of buildings, spans of bridges, pools and other structures. The relatively low price of Bicroelast TPP (compared to other modifications) allows you to create a reliable and durable roofing with optimal costs. Service life - up to 15 years. It is better to use Bikroelast, Technoelast or Uniflex with the EKP marking as the top layer for roofing.
In the Roofing and Insulation store, you can buy Bikroelast CCI produced by the TechnoNIKOL concern wholesale and retail at competitive prices. Our company also provides services for the delivery of rolled materials to facilities and provides qualified advice on their installation.
Reading time ≈ 3 minutes
Bikroelast is one of the latest generation of bituminous roofing materials, oriented to long-term operation (more than 10 years). It is used on roofs with a slight slope or for foundation waterproofing. The inability to use on roofs with a large slope is a disadvantage of this material.
Properties
The technical characteristics of bicroelast are based on the features of its base and protective layers. The basis is usually taken fiberglass, polyester or fiberglass. A high-quality modified bituminous composition endowed with astringent properties is applied to the base. This binder component is enriched with technological additives that significantly improve the characteristics of the material. The properties of bicroelast allow it to bend well at temperatures up to -10° and withstand heating up to +85°. This undeniable advantage makes it possible to use bicroelast in all climatic zones. A polymer film and a protective dressing are applied over the base; it can be coarse-grained (slate or asbagal) and fine-grained (sand).
Technical characteristics of bicroelast
Varieties of bicroelast
Since both the base and the protective layer may contain different components, separate types of bicroelast are distinguished. They are labeled with abbreviations. The first letter indicates the basis from which the material is made. T - fiberglass, E - polyester, X - fiberglass. The second letter is the designation of the top protective layer of the bikroelast vapor barrier. K - coarse-grained dressing. The third letter indicates the bottom protective layer. P - polyethylene film. Numerical designations show what is the weight of 1 sq.m of material. Accordingly, large numbers indicate a large thickness.
Bicroelast CCI made of fiberglass, which is coated on 2 sides with a polymer film. This is a very durable material that has found application as a lining. They are also used when it is necessary to make waterproofing of foundations, pools, bridges.
Bicroelast EKP is made on the basis of polyester, on which protection is applied in the form of a coarse-grained dressing, as well as a polymer film. It is used for arranging the top layer of the roof. It allows you to get high quality coverage at a very reasonable price.
Bicroelast HKP made of fiberglass coated with coarse-grained dressing and polymer film. This is an economy class material, it is used for arranging the top layer of the roof, which has a small slope (up to 10 °). Despite the low price, it is durable.
Bicroelast EPP- This is a kind of lining material based on polyester with a protection of a polymer film. Differs in elasticity and good waterproofing properties. It can be welded under any slope, so this type of bicroelast is used to create vertical waterproofing.
Bicroelast TKP made on the basis of fiberglass, which allows the material to be used on roofs subjected to loads. The result will be especially good if the substrate is made of CCI bicroelast. Coarse topping gives an attractive appearance roofing. In the photo you can evaluate how such a roof looks.
Features of use
With the help of this material, roofs are equipped, waterproofing of ground and underground structures is carried out. The durability of the operation of bicroelast is associated with the exact observance of all recommendations for its installation. Firstly, the base on which this rolled material is planned to be applied requires special attention. It must be thoroughly degreased, dust completely removed, usually a bituminous primer is used for this. Secondly, do not forget about the overlap, when the coating is applied with the help of a burner.
On the video you can see the technology of this work. According to reviews, the size of the overlap should not be less than 10 cm. The advantage of bicroelast during installation is that it is easier to heat it up with a burner than Technoelast, Rubitex, Stekloelast, Filizol, Uniflex, which are distinguished by their infusibility.
Video
One of the most common and remaining in demand today is the construction / material is roofing material. Its popularity is due to its versatility and low price. However, the fragility and insufficiently high parameters cause a lot of complaints about this product.
The TechnoNIKOL company, which regularly supplies various new products to the market, has launched the production of Bikroelast roofing material, which completely replaces roofing material. It is possible to call "TPP" its analogue only in the first approximation, since the characteristics of this product, properties and application specifics are strikingly different.
Features of "Bikroelast"
*Several varieties are produced under this brand. The article considers a product with the designation "CCI", although the differences from other samples are insignificant - in the structure and individual characteristics.
Firstly, this product simultaneously performs 2 functions - providing vapor and waterproofing. Consequently, in the process of finishing structural elements, there is no need to lay different protective layers.
Secondly, the "core" of the material is covered on both sides with the thinnest film. It is worth remembering that the roofing material is just cardboard impregnated with a bitumen composition.
Characteristics of Bicroelast TPP
- The temperature range in which the material does not lose its properties (ºС) is from -15 to +85.
- Moisture absorption - no.
- Elasticity, which makes it possible to fix the material on irregularities without the risk of damage.
- Rupture strength (N) - 800/900 (longitudinal / transverse directions).
- Protective coating - film (without a logo on the front side; with a logo - on the back, built-up).
- Web thickness (mm) - 4.
- Standard roll dimensions (m) - 15 x 1.
- Weight (kg): roll - 45, 1 m2 - 3.
Scope of use
Bikroelast TPP is used for waterproofing roofs (it is laid at the bottom of the so-called "pie") or other parts of the structure of structures.
Mounting technology
It should be noted once again that "Bikroelast TPP" cannot be used as a surface protection of the base. It must necessarily be “covered” with another material (mastic, cladding or other “finish” coating). This is due to the low resistance of its protective film to external factors, primarily ultraviolet radiation.
Fixation of canvases on the basis is carried out by welding. Therefore, when working, you will need an open flame source (blowtorch, gas burner). All preparatory measures are standard (surface cleaning, etc.).
Price
In relation to the Moscow region - from 77.8 rubles / m². For roofing material, this figure is about 19 rubles / m². But given that the service life of the latter is at most 4 years, and Bikroelast is at least 10, and you don’t need to spend money on vapor barrier material, it’s not so difficult to determine which is preferable.
Class "STANDARD", brand of CCI, which is produced Russian company"Technonikol". Waterproofing BIKROELAST TPP is a lining modified built-up waterproofing material, which has a five-layer structure and is produced by applying a bitumen-polymer binder mixture on a polyester base on both sides, and having an upper and lower protective homogeneous layer.
BIKROELAST TPP waterproofing sheet is made of the following materials: glass-base BIKROELAST TPP is a glass fabric, which is a woven dense fabric with a high tensile strength, SBS-modified bitumen-polymer mixture is applied on both sides of it, consisting of bitumen, styrene-butadiene thermoplastic and special filler, then a protective layer is applied, from above and below the protective layer consists of a welded polymer film.
The structure of the waterproofing material BIKROELAST TPP
1. Top protective coating: polymer film
2. Base material: fiberglass
3. Bottom protective coating: polymer film
Bituminous waterproofing material BIKROELAST TPP class "STANDARD" waterproofing TECHNONICOL, has high water resistance and wear resistance, good frost resistance and heat resistance, which allows it to withstand high temperature loads and their fluctuations, this material is also elastic and durable, its service life is at least 10- 15 years. BIKROELAST TPP lining waterproofing material is produced in rolls 15 m long and 1 m wide, the weight of the roll is 45 kg, and the delivery is carried out on a pallet, the volume of which is 23 rolls.
Application of BICROELAST TPP TECHNONICOL
Bituminous waterproofing material BIKROELAST TPP is used for the installation and repair of the lower layer of the roofing carpet of the roof of residential and industrial buildings and structures. Fiberglass, which is the basis of the waterproofing material BIKROELAST TPP, has a high tensile strength, this property allows this material to be used as a lining waterproofing layer in mobile or mechanically impacted roof structures - exploited and loaded roofs. Also, the waterproofing material BIKROELAST TPP can be used for waterproofing vertical and horizontal surfaces of the foundation, waterproofing basements and tunnels, waterproofing floors.
The rolled waterproofing material BIKROELAST TPP has flexibility on the beam R=25 mm, not higher than -10C, the brittleness temperature of the bitumen layer is up to -25C and heat resistance + 85C, so it can be used in all climatic conditions (SNiP 23-01). The connection of the canvases to each other is carried out by the method of fusing with fire using a gas burner, and the laying of the canvas should take place on a prepared primed base. When waterproofing a two-layer roof, it is recommended to use BIKROELAST TPP with roofing waterproofing material BIKROELAST TKP, which is used as the lower waterproofing layer of the roof.
Specifications BIKROELAST TPP TECHNONICOL
Name |
Meaning |
|
BICROELAST |
CCI |
|
Manufacturer |
TechnoNIKOL |
|
Length / width, m |
15x1 |
|
Weight 1 m2, kg, (±0.25 kg) |
|
|
The basis |
fiberglass |
|
Breaking strength in the longitudinal/transverse direction, N, not less than |
800/900 |
|
Flexibility temperature on the beam R=25 mm and R=10 mm, °С, not higher |
|
|
Binder brittleness temperature, °C, not higher |
|
|
Heat resistance, °С, not less than |
|
|
Water absorption within 24 hours, % by mass, no more |
|
|
Type of protective coating - top side |
film without logo |
|
Type of protective coating - welded side |
film with logo |